it-swarm.it

Come posso impostare VLAN?

Ho un server DAAP con più VLAN. Vorrei che il traffico venisse inoltrato su tutte le VLAN. Inoltrato da eth0 a eth1.010 * Ho lo switch configurato per essere un porta trunk con le VLAN corrette e ho abilitato / proc/sys/net/ipv4/ip_forward

Ma questo non sembra fare il trucco. C'è qualcos'altro che devo fare?

Ecco i miei risultati ifconfig, come puoi vedere VLAN non stanno realmente ricevendo traffico:

eth0      Link encap:Ethernet  HWaddr 00:14:d1:10:ca:fc  
          inet addr:192.168.1.20  Bcast:172.21.255.255  Mask:255.255.0.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:536 errors:0 dropped:0 overruns:0 frame:0
          TX packets:259 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:264232 (258.0 KiB)  TX bytes:37425 (36.5 KiB)
          Interrupt:20 Base address:0xe000 

eth1      Link encap:Ethernet  HWaddr 00:1c:c4:31:28:22  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:303 errors:0 dropped:0 overruns:0 frame:0
          TX packets:202 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:225213 (219.9 KiB)  TX bytes:47118 (46.0 KiB)
          Interrupt:17 

eth1.0101 Link encap:Ethernet  HWaddr 00:1c:c4:31:28:22  
          inet addr:172.17.1.20  Bcast:172.17.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:9076 (8.8 KiB)

eth1.0102 Link encap:Ethernet  HWaddr 00:1c:c4:31:28:22  
          inet addr:172.18.1.20  Bcast:172.18.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:9076 (8.8 KiB)

eth1.0103 Link encap:Ethernet  HWaddr 00:1c:c4:31:28:22  
          inet addr:172.19.1.20  Bcast:172.19.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:9076 (8.8 KiB)

eth1.0104 Link encap:Ethernet  HWaddr 00:1c:c4:31:28:22  
          inet addr:172.20.1.20  Bcast:172.20.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:9076 (8.8 KiB)

eth1.0105 Link encap:Ethernet  HWaddr 00:1c:c4:31:28:22  
          inet addr:172.21.1.20  Bcast:172.21.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:40 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:9076 (8.8 KiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:113 errors:0 dropped:0 overruns:0 frame:0
          TX packets:113 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:20777 (20.2 KiB)  TX bytes:20777 (20.2 KiB)

Ecco il mio file/etc/network/interfaces:

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# Automagically configured network interfaces
auto eth0
auto eth1.0101
auto eth1.0102
auto eth1.0103
auto eth1.0104
auto eth1.0105

iface eth0 inet static
   address 192.168.1.20
   netmask 255.255.0.0
   gateway 192.168.1.3
   network 172.21.0.0
   broadcast 172.21.255.255

iface eth1.0101 inet static
   address 172.17.1.20
   netmask 255.255.255.0


iface eth1.0102 inet static
   address 172.18.1.20
   netmask 255.255.255.0


iface eth1.0103 inet static
   address 172.19.1.20
   netmask 255.255.255.0


iface eth1.0104 inet static
   address 172.20.1.20
   netmask 255.255.255.0


iface eth1.0105 inet static
   address 172.21.1.20
   netmask 255.255.255.0

Grazie per qualsiasi aiuto, ci sto lavorando da un po '.

3
chris

Ha funzionato! Ho un problema separato con DAAP ora, ma penso che sia legato ad Avahi. Proverò a risolverlo da solo. Grazie mille.

0
chris

Non l'ho fatto su Ubuntu, ma ecco la mia ricerca finora:

Devi restare

vconfig add eth1 101  
vconfig add eth1 102  
vconfig add eth1 103  
vconfig add eth1 104  
vconfig add eth1 105

in uno script di avvio.

Il file delle interfacce sarebbe simile al seguente:

auto lo
iface lo inet loopback
auto eth0 eth1 vlan2 vlan3 vlan4 vlan5
iface eth0 inet dhcp

# VLAN 1 - native management VLAN
iface eth1 inet static
        address 10.0.0.1
        netmask 255.255.255.224
        vlan_raw_device eth1

# VLAN 2 - DMZ
iface vlan2 inet static
        address 10.0.0.33
        netmask 255.255.255.224
        vlan_raw_device eth1

# VLAN 3 - Accounting
iface vlan3 inet static
        address 10.0.0.65
        netmask 255.255.255.224
        vlan_raw_device eth1

# VLAN 2 - DMZ
iface vlan2 inet static
        address 10.0.0.33
        netmask 255.255.255.224
        vlan_raw_device eth1

# VLAN 3 - Accounting
iface vlan3 inet static
        address 10.0.0.65
        netmask 255.255.255.224
        vlan_raw_device eth1

# VLAN 4 - Engineering
iface vlan4 inet static
        address 10.0.0.97
        netmask 255.255.255.224
        vlan_raw_device eth1

# VLAN 5 - Sales & Marketing
iface vlan5 inet static
        address 10.0.0.129
        netmask 255.255.255.224
        vlan_raw_device eth1

Utilizzerai i tuoi IP nel file delle interfacce, ovviamente. Facci sapere se ha funzionato.

Riferimenti: 12

4
Li Lo

Se sto leggendo correttamente la tua domanda, stai cercando un ponte. Il bridging inoltra tutto il traffico da un'interfaccia all'altra.

Dovrai installare il pacchetto bridge-utils e impostare la tua configurazione come segue:

auto br0
iface br0 inet static
  address 192.168.1.20
  netmask 255.255.0.0
  gateway 192.168.1.3
  bridge_ports eth0 eth1.0101 eth1.0102 eth1.0103 eth1.0104 eth1.0105

Non è richiesta alcuna configurazione per le singole porte.

Ciò configurerà le porte in un unico bridge e dovrebbe rendere tutto accessibile. Puoi vedere lo stato del bridge con il comando brctl.

0
Ressu